1～15 item / All 33 items
Easy and quick to measure, allowing for frequent quality control of on-site concrete strength.
If you have any questions regarding the introduction below, please feel free to contact us.
It is a non-destructive testing device used worldwide for measuring ultrasonic pulse velocity.
Next-generation ultrasonic testing machine
This is a compact and lightweight penetration testing machine developed by the Civil Engineering Research Institute for slope investigation.
***Features*** - It was devised at the Ministry of Construction's Civil Engineering Research Institute, and it can measure the relationship between the number of impacts of a weight and the amount of penetration, allowing for the assessment of the relative bearing capacity strength of road subgrades and the determination of bearing capacity values, similar to the purposes of CBR tests and plate load tests (N value (Nd value) is obtained). - Continuous data from the surface to the required depth can be obtained, eliminating concerns about underestimating the influence of the lower layers of the subgrade. - It is also used for inspections of restoration work after the completion of road gas and telephone line construction.
We will determine the ground reaction coefficient K value for the road. The dial gauge used to measure the settlement is a 4-point measurement type. It is a 10-ton oil jack system.
***Features*** - It is a four-point measurement system that measures the settlement amount at four locations on the loading plate. - The test jack is a 10-ton oil jack type.
JIS R 5201 compliant product.
This is a notice from Rex Co., Ltd. regarding the "Mortar Flow Tester C-206."
This is a testing device for slump tests and slump flow tests of fresh concrete.
***Features*** - It is the most common testing instrument for measuring the consistency of mixed concrete. - It complies with JIS A 1101 standards.
This is a flow table for mortar flow tests. The flow value is measured by the up and down movement of the disc caused by the rotation of the camshaft.
***Features*** - It determines the flow value of the mortar by measuring the flow value through the up and down movement of a disc caused by the rotation of a camshaft. - It complies with IS R 5201 standards.
A DC signal generator that can perform generation and measurement simultaneously.
In pressure tests and insulation resistance tests, issues such as erroneous test results due to disconnection or poor contact of test leads, and the impact of fluctuations in test voltage caused by variations in power supply voltage have been pointed out.
This seeks to determine the relationship between the dry density and moisture content when the soil is compacted.
The JIS Compaction Test Device S-171 complies with JIS A1210 and is used to determine the relationship between dry density and moisture content when soil is compacted. It is utilized in the design and management of compaction for constructing roads, embankments, and subgrades, as well as for managing optimal moisture content and compaction degree. Additionally, it serves as a means to prepare soil specimens for CBR tests, unconfined compression tests, and more. 【Features】 ○ Complies with JIS A1210 ○ Can also be used as a means to prepare soil specimens for CBR tests, unconfined compression tests, etc. For more details, please contact us.
From gas pressure control to hydraulic pressure control. A fully automatic in-house loading test device that does not use high-pressure gas.
The in-situ horizontal load test is a common field test used to understand the horizontal strength characteristics of the ground for pile design. Until now, the in-situ horizontal load testing equipment has been operated manually, leading to variations in testing accuracy due to individual differences. However, with automation, it will be possible to obtain test results with consistent accuracy. 【Features】 - Fully automated on-site loading test equipment that does not use high-pressure gas - Lightweight and easy to handle due to the use of hydraulic pressure For more details, please contact us.
Measuring without variation in all directions, from soft materials to hard materials.
The Echo Chip 3 hardness testing machine is the most precise and functionally rich high-spec model in the Echo Chip series. It can be converted to various hardness scales such as HV, HB, HR, and HS. It can measure everything from soft materials to hard materials without variation in any direction. 【Features】 ○ Can be converted to any hardness scale (HV, HB, HR, HS) ○ No personal error at all ○ User-defined conversion formulas can be programmed ○ Complies with ASTM and DIN standards For more details, please contact us or download the catalog.
Easily measure cross-sectional changes! Testing device for diagnosing the characteristics of cracks and other issues.
The Integrity Testing Device PIT-X can easily measure the tip position, cracks, and cross-sectional changes of various piles. It is a device that diagnoses the properties of piles, such as pile length, changes in pile cross-section, and cracks, by utilizing the phenomenon where elastic waves generated by striking the pile reflect at boundaries with different impedances. 【Features】 ○ Latest compact model consisting of wireless sensors and a pocket PC ○ Complies with the American technical standard ASTM D5882 Please contact us for more details.
The measurement time is very short! A simple bearing capacity testing machine that can be operated by one person.
"Elefoot" is a ground bearing capacity testing device that measures the support capacity of surface soil in a simple manner. By utilizing a person's body weight as a reaction force, there is no need for large equipment such as heavy machinery or power supplies. In addition to a short measurement time, it can be operated by a single person and is capable of measuring in confined spaces. 【Features】 ■ Extremely short measurement time, can be operated by one person ■ Capable of measuring ground bearing capacity in confined spaces ■ Lightweight and easy to carry ■ Ideal for soil conditions with low viscosity, such as clay to sandy soils ■ Capable of measuring bearing capacities from 0 to 4375 kN/m² *For more details, please refer to the catalog or feel free to contact us.
Easy operation with a touchscreen! All-in-one hardness testing solution.
The "equotip550" is an ideal hardness testing machine for on-site testing of heavy large parts or assembled components. By exchanging the impact device, it accommodates a wide range of hardness scales. Furthermore, the compact portable model can be used in various locations, including on-site, in factories, and in laboratories. The use of icons makes touch screen operation even easier, and the user interface features a clear design for smooth operation. 【Features】 ■ High-resolution display ■ Comes with a cover to prevent scratches and dirt on the monitor when not in use ■ Testing accuracy of ±0.8μm, with high precision and excellent reproducibility of up to ±1.0HRC ■ Ability to incorporate unique conversion curves ■ Usable on thin parts; suitable for pipes and irregular materials For more details, please feel free to contact us.
Regular inspections for electrical equipment and tools to check for leakage and disconnection! Achieving convenience through regular maintenance.
It covers all the necessary measurements for testing equipment, such as insulation resistance measurement, leakage current measurement, load current measurement, voltage measurement, and leakage breaker tests, all in one device. It is a handy type with a simple operation method. The measurement results are easy to understand for beginners, with "green for pass and red for fail." *For more details, please refer to the catalog available for download below under "PDF Download." You can also request a quote through "Contact Us." Feel free to reach out.
